Skip to content
H & J EximHome Textile Manufacturer & Exporter
Back to Buyer Guides

Product Development

Colour Fastness on Linen: Why Deep Colours Need More Care

Published

Colour fastness is how well a dyed cloth holds its colour against washing, rubbing, light and perspiration, graded on standard scales from a test laboratory. Deep and dark shades need more care because they carry more dye, so there is more loose colour to rub off or wash out, and any loss shows more plainly against the base cloth. On linen the risk is real but manageable: specify the fastness grades you need, approve a lab dip against them, and confirm the result on a bulk-representative sample before you ship.

What colour fastness actually measures

Fastness is not one number. It is a set of tests, each for a different thing the finished product will meet in use, and each reported on its own scale. Two scales do most of the work. The grey scale runs 1 to 5 and rates two separate things: how much the dyed cloth itself changed (colour change) and how much colour it transferred onto a neighbouring white fabric (staining). Light fastness uses the blue wool scale, 1 to 8, where a higher number means slower fading. On both, higher is better, and a half grade such as 4 or 5 is normal reporting.

A buyer does not need to run the tests, but should know which ones to call for and what grade to ask of each. The methods below are the common international ones. They are test procedures, not certificates, and any competent textile laboratory can run them.

The fastness tests worth naming in a spec

Test Common method What it simulates Scale
Wash fastness ISO 105-C06 Domestic or commercial laundering Grey, 1 to 5
Rubbing (crocking), dry and wet ISO 105-X12 Colour rubbing onto skin, other cloth or upholstery Grey, 1 to 5
Light fastness ISO 105-B02 Fading under daylight or display lighting Blue wool, 1 to 8
Perspiration ISO 105-E04 Sweat on bedding, napkins and apparel-adjacent goods Grey, 1 to 5
Water ISO 105-E01 Damp storage and contact when wet Grey, 1 to 5

Which tests matter depends on the product. Bed linen and table linen are washed often, so wash and rubbing fastness lead. Curtains and anything on long display live under light, so light fastness leads there. Napkins and anything in contact with skin for hours bring perspiration into the picture. Match the test to how the product is used, rather than asking for top grades on everything, which raises cost without buying you anything.

Why deep and dark shades are the hard case

The reason deep colours need more care is mostly about dye load. A pale stone or oatmeal shade is reached with a small quantity of dye, most of which fixes to the fibre. A charcoal, a navy, a deep terracotta or an inky slate needs far more dye in the bath, and no dyeing is fully efficient, so more unfixed dye is left sitting on the fibre surface. That surplus is what crocks off onto skin and white cloth in the first few uses, and what bleeds in the first wash.

Linen adds its own character. The fibre takes dye less evenly than fine cotton because the filaments vary along their length, which is part of why linen looks alive rather than flat. The slubs and the natural colour variation that make linen attractive also mean a dark shade can look slightly uneven, and any crocking is more visible against a dark ground. None of this makes deep colours unworkable. It means they carry less margin for a thin process, so the after-treatment that removes surplus dye, the soaping-off and rinsing, matters more than it does on a pale shade.

Light fastness is the second watch point. Deep blues and some bright reds are chemically more prone to fading under strong light than earth tones and neutrals. For a product that will sit in a sunlit window or under retail lighting for months, this is worth testing specifically rather than assuming.

What good grades look like in practice

As a rough guide for home textiles, wash and rubbing fastness of 4 or better, and perspiration of 4 or better, are reasonable to ask for on most dyed linen. Dry rubbing should sit higher than wet rubbing, and wet rubbing on a very dark shade is the figure most likely to fall short, so it is the one to check first. For light fastness, 4 to 5 on the blue wool scale suits most bedding, while curtains and long-display goods are better at 5 to 6. Treat these as a starting point to agree with your supplier for your market and product, not as a universal pass mark.

Writing fastness into your specification

Vague instructions such as "must not bleed" cannot be tested or enforced. Put numbers against named methods instead, so that a sample can pass or fail against something written down.

  • State the test method and the minimum grade for each fastness that matters to the product, for example wash fastness ISO 105-C06 grade 4 minimum.
  • Say which colours the requirement applies to. It is normal to set a tighter rubbing grade on your darkest shades and accept a slightly lower wet-rubbing figure where the whole palette cannot meet it, as long as you decide that knowingly.
  • Call for AZO-free dyes if your market requires it, and keep the restricted-substance limits your market sets as a separate line in the spec.
  • Ask for the care label to match the tested behaviour. A deep shade is often best labelled for a cooler, separate first wash, which protects the colour and sets honest expectations with the end customer.
  • Require the fastness test to be run on a bulk-representative sample, not only on the first lab dip, since a shade can behave differently once it is dyed at production scale.

H & J Exim matches colour to Pantone TCX references, issues lab dips and strike-offs for your approval, and runs AZO-free dyes. Colours shown on screen are indicative; the lab dip is what confirms the shade before anything goes to bulk. The core palette includes deep shades such as charcoal, navy, terracotta, clay and slate blue, and any quality can be dyed to your own reference. For how approval works step by step, see How Colour Matching Works. If the depth of colour is central to your product, garment-dyed linen is worth reading alongside this, because where the dye enters the process changes how fastness behaves.

To discuss a specific palette or test requirement, see the product range or get in touch.

Common questions

Does linen bleed more than cotton?

Not inherently. Bleeding is a function of dye depth and how thoroughly surplus dye is washed off, not of the fibre alone. A well-processed deep linen can hold colour as well as cotton. Linen's uneven dye uptake means a dark shade may look slightly less flat, which is a different thing from poor fastness.

Why does my dark linen rub off a little at first?

Early crocking is usually surplus unfixed dye on the fibre surface, worst on the deepest shades. It should settle after the first wash or two. If it continues, the wet rubbing grade is likely too low and should be checked against the test, rather than treated as normal.

Can I get a very dark navy or black with high fastness?

Yes, but these are the shades where fastness, especially wet rubbing and light fastness, is most likely to be the limiting factor, so test them specifically and approve a bulk-representative sample. Agree in advance which grade you will accept if the darkest shade in a palette cannot match the lighter ones.

Should deep colours have a different care label?

Often yes. A cooler first wash, washing dark shades separately, and avoiding prolonged direct sunlight all protect a deep colour and reduce the chance of a complaint. The label should reflect how the cloth actually tested.

Ready to talk about your programme?

Share your brief, tech pack or reference sample and we will come back to you within 1 to 2 business days.

Designs ready?Request a direct quoteSend your tech pack, sizes and quantities in one go. Quote within 2 business days.